1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
<?xml version="1.0" encoding="ISO-8859-1"?>
<!DOCTYPE sect1 PUBLIC "-//OASIS//DTD DocBook XML V4.5//EN"
"http://www.oasis-open.org/docbook/xml/4.5/docbookx.dtd" [
<!ENTITY % general-entities SYSTEM "../general.ent">
%general-entities;
]>
<sect1 id="ch-scripts-clock">
<?dbhtml filename="clock.html"?>
<title>Configuring the system clock</title>
<indexterm zone="ch-scripts-clock">
<primary sortas="d-clock">clock</primary>
<secondary>configuring</secondary></indexterm>
<para>This section discusses how to configure the
<command>systemd-timedated</command> system service, which configures
system clock and timezone.</para>
<para>If you cannot remember whether or not the hardware clock is set to UTC,
find out by running the <userinput>hwclock --localtime --show</userinput>
command. This will display what the current time is according to the hardware
clock. If this time matches whatever your watch says, then the hardware clock is
set to local time. If the output from <command>hwclock</command> is not local
time, chances are it is set to UTC time. Verify this by adding or subtracting
the proper amount of hours for the timezone to the time shown by
<command>hwclock</command>. For example, if you are currently in the MST
timezone, which is also known as GMT -0700, add seven hours to the local
time.</para>
<para><command>systemd-timedated</command> reads <filename>/etc/adjtime</filename>,
and depending on the contents of the file, it sets the clock to either UTC or
local time.</para>
<para>Create the <filename>/etc/adjtime</filename> file with the following contents
if your hardware clock is set to local time:</para>
<screen role="nodump"><userinput>cat > /etc/adjtime << "EOF"
<literal>0.0 0 0.0
0
LOCAL</literal>
EOF</userinput></screen>
<para>If <filename>/etc/adjtime</filename> isn't present at first boot,
<command>systemd-timedated</command> will assume that hardware clock is
set to UTC and adjust the file according to that.</para>
<para>You can also use the <command>timedatectl</command> utility to tell
<command>systemd-timedated</command> if your hardware clock is set to
UTC or local time:</para>
<screen role="nodump"><userinput>timedatectl set-local-rtc 1</userinput></screen>
<para><command>timedatectl</command> can also be used to change system time and
time zone.</para>
<para>To change your current system time, issue:</para>
<screen role="nodump"><userinput>timedatectl set-time YYYY:MM:DD HH:MM:SS</userinput></screen>
<para>Hardware clock will also be updated accordingly.</para>
<para>To change your current time zone, issue:</para>
<screen role="nodump"><userinput>timedatectl set-timezone TIMEZONE</userinput></screen>
<para>You can get list of available time zones by running:</para>
<screen role="nodump"><userinput>timedatectl list-timezones</userinput></screen>
<note><para>Please note that <command>timedatectl</command> command can
be used only on a system booted with systemd.</para></note>
<sect2>
<title>Network Time Synchronization</title>
<para>Starting with version 214, systemd ships a daemon called
<command>systemd-timesyncd</command> which can be used to
synchronize the system time with remote NTP servers.</para>
<para>The daemon is not intended as a replacement for the well
established NTP daemon, but as a client only implementation
of the SNTP protocol which can be used for less advanced
tasks and on a resource limited systems.</para>
<para>To enable the <command>systemd-timesyncd</command> daemon,
issue the following command:</para>
<screen role="nodump"><userinput>systemctl enable systemd-timesyncd</userinput></screen>
<para>The <filename>/etc/systemd/timesyncd.conf</filename> file
can be used to change the NTP servers that
<command>systemd-timesyncd</command> synchronizes with.</para>
</sect2>
</sect1>
|
