1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
<?xml version="1.0" encoding="ISO-8859-1"?>
<!DOCTYPE sect1 PUBLIC "-//OASIS//DTD DocBook XML V4.4//EN"
"http://www.oasis-open.org/docbook/xml/4.4/docbookx.dtd" [
<!ENTITY % general-entities SYSTEM "../general.ent">
%general-entities;
]>
<sect1 id="ch-scripts-network">
<?dbhtml filename="network.html"?>
<title>Configuring the network Script</title>
<indexterm zone="ch-scripts-network">
<primary sortas="d-network">network</primary>
<secondary>configuring</secondary></indexterm>
<para>This section only applies if a network card is to be
configured.</para>
<para>If a network card will not be used, there is likely no need to
create any configuration files relating to network cards. If that is
the case, remove the <filename class="symlink">network</filename>
symlinks from all run-level directories (<filename
class="directory">/etc/rc.d/rc*.d</filename>).</para>
<sect2>
<title>Creating Network Interface Configuration Files</title>
<para>Which interfaces are brought up and down by the network script
depends on the files and directories in the <filename
class="directory">/etc/sysconfig/network-devices</filename> hierarchy.
This directory should contain a sub-directory for each interface to be
configured, such as <filename>ifconfig.xyz</filename>, where
<quote>xyz</quote> is a network interface name. Inside this directory
would be files defining the attributes to this interface, such as its IP
address(es), subnet masks, and so forth.</para>
<para>The following command creates a sample <filename>ipv4</filename>
file for the <emphasis>eth0</emphasis> device:</para>
<screen><userinput>cd /etc/sysconfig/network-devices &&
mkdir -v ifconfig.eth0 &&
cat > ifconfig.eth0/ipv4 << "EOF"
<literal>ONBOOT=yes
SERVICE=ipv4-static
IP=192.168.1.1
GATEWAY=192.168.1.2
PREFIX=24
BROADCAST=192.168.1.255</literal>
EOF</userinput></screen>
<para>The values of these variables must be changed in every file to match
the proper setup. If the <envar>ONBOOT</envar> variable is set to
<quote>yes</quote> the network script will bring up the Network Interface
Card (NIC) during booting of the system. If set to anything but
<quote>yes</quote> the NIC will be ignored by the network script and not
be brought up.</para>
<para>The <envar>SERVICE</envar> variable defines the method used for
obtaining the IP address. The LFS-Bootscripts package has a modular IP
assignment format, and creating additional files in the <filename
class="directory">/etc/sysconfig/network-devices/services</filename>
directory allows other IP assignment methods. This is commonly used for
Dynamic Host Configuration Protocol (DHCP), which is addressed in the
BLFS book.</para>
<para>The <envar>GATEWAY</envar> variable should contain the default
gateway IP address, if one is present. If not, then comment out the
variable entirely.</para>
<para>The <envar>PREFIX</envar> variable needs to contain the number of
bits used in the subnet. Each octet in an IP address is 8 bits. If the
subnet's netmask is 255.255.255.0, then it is using the first three octets
(24 bits) to specify the network number. If the netmask is 255.255.255.240,
it would be using the first 28 bits. Prefixes longer than 24 bits are
commonly used by DSL and cable-based Internet Service Providers (ISPs).
In this example (PREFIX=24), the netmask is 255.255.255.0. Adjust the
<envar>PREFIX</envar> variable according to your specific subnet.</para>
</sect2>
<sect2 id="resolv.conf">
<title>Creating the /etc/resolv.conf File</title>
<indexterm zone="resolv.conf">
<primary sortas="e-/etc/resolv.conf">/etc/resolv.conf</primary>
</indexterm>
<para>If the system is going to be connected to the Internet, it will
need some means of Domain Name Service (DNS) name resolution to
resolve Internet domain names to IP addresses, and vice versa. This is
best achieved by placing the IP address of the DNS server, available
from the ISP or network administrator, into
<filename>/etc/resolv.conf</filename>. Create the file by running the
following:</para>
<screen><userinput>cat > /etc/resolv.conf << "EOF"
<literal># Begin /etc/resolv.conf
domain {<replaceable>[Your Domain Name]</replaceable>}
nameserver <replaceable>[IP address of your primary nameserver]</replaceable>
nameserver <replaceable>[IP address of your secondary nameserver]</replaceable>
# End /etc/resolv.conf</literal>
EOF</userinput></screen>
<para>Replace <replaceable>[IP address of the nameserver]</replaceable>
with the IP address of the DNS most appropriate for the setup. There will
often be more than one entry (requirements demand secondary servers for
fallback capability). If you only need or want one DNS server, remove the
second <emphasis>nameserver</emphasis> line from the file. The IP address
may also be a router on the local network.</para>
</sect2>
</sect1>
|
